Hyperlink Function of green laser pointer with Remote Control

Hyperlink Function of green laser pointer with Remote Control
LTS-YAG laser texturing equipment for China’s large, medium and small-scale cold-rolled sheet plant to improve reliable means of cold-rolled hair. Increase the service life 3-5 times roll, increase rolling speed. Product quality rate increased by 30% below 0.5mm thick plate (with) pass rate increased by 30%. In the international market, price of laser hair of the board than the industry blasting hair of about 10% of your plate. Using the LTS-YAG laser texturing equipment, three shifts per day of continuous work, the whole equipment, the price is only imported EDT 1 / 5, or even laser texturing equipment abroad quotes, foreign exchange equivalent to RMB 30 million, even if the second behalf of the EDM texturing equipment, only 2,500 watts of power, the price is also reported $ 18 million. Besides, the sensitivity of the delicate parts insidegreen laser pointerwon’t reduce as time goes by.
Now the user has been completely dependent on laser-textured work roll and the rolling roll production, actual production data shows that the laser hair system does greatly improve the speed of plate rolling and product quality. Six months later, before the roll of the cracks, there is no collapse of the basic situation, the original base of each plant has a lot of waste roll, now roll with a 200mW green Laser Pointer texturing after the roll is basically only a few other reasons because it scrapped off, for the user to save a lot of purchase, the cost of roll maintenance, saving the cost of production. Has a special cold-rolled steel sheet surface topography in the manufacturing of a wide range of applications, especially in the automotive and appliance industries. In the cold-rolled steel sheet production and application of research, it was discovered that the surface morphology of a series of cold-rolled sheet steel stamping parameters on the nature of the coating process performance such as brightness, after have a major impact, and surface morphology of cold-rolled plate in turn, is largely dependent on the production process of cold rolling work rolls and rolls of flat surface morphology. green laser pointer can achieve the free presentation of the electronic documents.
In essence, the rolled steel sheet surface topography is roll attenuation of surface topography “copy.” Therefore, the study, control and cold-rolled steel cold ROLLING roller surface morphology of the hair roller technology came into being. Roll hair texturing technologies including steel and its surface morphology study of the relationship between process performance, roll texturing process of texturing equipment research and development. Since the 1980s, the advanced industrial countries to roll texturing techniques put a lot of research and industrial applications, with the automotive, appliance and other industries, cold-rolled sheet of a higher quality requirements. Cold-rolled steel sheet surface topography and process performance study, in order to improve the performance of cold-rolled steel plate stamping and coating process performance such as brightness, describes the surface morphology of cold-rolled plate, including the introduction of surface roughness, including the traditional range of parameters as a criterion. Simple 100mW green laser pointer is without any other function like turning over page through remote control.
Surface roughness Ra: Ra texturing roller is generally between l ~ 10μm. Ra greater help to improve the performance of short-stamping and coating material solidity, and Ra is small, will help improve the brightness of the light sheet after coating. Peak density of PPI: defined as the length of every inch of the surface height is greater than 1.27 m peak number. PPI higher the value, the better coating adhesion. Waviness wca: steel surface was uneven in different wavelength cycles. More than a few parameters, is an independent description of the surface morphology of cold-rolled plate, but also influence each other. One of the most studied is the surface roughness Ra. Cold-rolled strip surface finishing methods can be divided according to their hair and bright surface of the two. Processing can maintain bright metallic luster as bright as mirror, chrome parts as (car, bicycle, household appliances) of the original board. As the surface roughness after processing is also affected by grain size effects, need to use fine grain (8 to 10) of the plate. 50mW blue violet laser pointer is also popular in other developed countries.
Rough surface with micro-machining of convex and concave surfaces, also known as skins like processing, most are of this type of cold-rolled strip, a small indentation has the following characteristics: the stamping process, because the oil can be stored, so easily processed; can improve the coating adhesion; in strip processing is not easy to produce small scars, even had not evident. Face processing in the hair, as a general processing, Ra value (roughness average) to about 1.0 microns more appropriate, such as refrigerators, gas meter plate, steel furniture, etc., are not subjected to the basic stamping to electrode position plating film more. Compared with these, galvanized steel and galvanized steel color of the hair surface should be smaller. The laser beam of green laser pointer with remote control is very stable.

related green laser pointer blog:

led flash light

Hyperlink Function of green laser pointer with Remote Control